Rotary dampers, speed control dampers

The MT.-type mounts are used in cases where light or heavy machines should not be fixed to the floor or ground.

Efdyn's continuous rotation dampers and dashpots are used to dampen drives, control speed, and many other applications. These rotary dampers are the most rugged and durable units on the market. Efdyn viscous dampers are available in either ...

Diameter: 10 mm

Damping rate is reduced by increases in fluid temperature (and increased by reduction in temperature). The graph below indicates the percentage change in damping rate with temperature, relative to the rate quoted at 20?C. Dashpots compensated ...

Diameter: 15 mm

Ferrotec presents inertia dampers. When a stepper motor runs at its natural frequency, it may undergo too much settling time, vibration and acoustic noise. A Ferrofluidic damper uses ferrofluid for absorption of motion energy through ...

Diameter: 40 mm

ITT Enidine Inc. rate controls have been designed for regulation of speed or time necessary for movement of mechanisms between two positions. They provide superior performance using time-tested technology. They are suitable for controlling ...

These Viscous Speed Governors (VGS) are light but durable, and are appropriate for use in a wide variety of applications. These units use a silicone based viscous shearing technique to manage the rotation of shafts and hinged loads. ...

The SDS-C100 DOWNWARD-OPENING FLAP introduced by Lapcon is made up of bright nickel and zinc alloy. It has a 3.5x14/(M5*28) available screws with a door height of xl/2x torque. The device weights 35-50kg- cm(30-43 lbs- inch) per piece ...

The SDS-C30 1N is made of zinc alloy, steel and plastic. It is supplied with screws measuring 3.5 x 14. If installed per piece, it has 40-60kg-cm or 35-60lbs-inch. For the pair, it has 80-140kg-cm or 70-120lbs-inch. The recommended ...

The Lapcon-Dampers are made of a zinc alloy with a bright nickel finish. They are available with drop, butt or piano hinges and screws. The measurement of the torque is door height x l/2x door and the weight per piece is 1.96-6.86Nm ...

The LAPCON DAMPER NSDX-20 Top Opening Flap from SUGATSUNE KOGYO can open from 70? to 105? due to the oval mounting plate holes. These zinc alloy bright nickel finished hinges fully opens the flap, and may be used with butt, piano, or ...

The NSDX 35 2S UPWARD-OPENING FLAP introduced by Lapcon is composed of bright nickel and zinc alloy. It provides an opening angle alterable from 80? to 100? with a 3.5x15 available screws. In addition, the product offers two stop types ...

Diameter: 29, 37, 20 mm

These are hydraulic dampers manufactured by Bansbach? easylift. They offer speed in push-in and push-out directions. The speed can be controlled in both the directions. By turning the rod of the piston, the damping intensity can be tuned ...

Diameter: 8 mm
Maximum length: 45 mm
Force: 11 N

Diameter: 8 mm
Maximum length: 35 mm
Force: 11 N

Diameter: 8 mm
Maximum length: 10 mm
Force: 8 N - 170 N

Diameter: 9.9 mm
Maximum length: 20, 15 mm
Force: 85 N - 340 N

The DICTATOR oil dampers come with fixings that are attached to both ends and they are used in all locations where moved items, example flaps, operating arms and covers should not go beyond a certain speed. These units are attached to ...

Manufactured by Dictator Technik, the LD series is a type of hydraulic rotation damper. The series gives a constant speed control on long travel distances, especially on sliding doors. The dampers can be adapted to any respective application, ...

Maximum length: 235 mm - 273 mm
Minimum length: 165 mm - 203 mm
Force: 60 N - 120 N

Diameter: 10, 20, 30 mm
Maximum length: 105, 160, 60 mm

Diameter: 6 cm - 31 cm
Maximum length: 7 mm - 60 mm

Diameter: 3 mm - 35 mm
Maximum length: 18.7 mm - 215 mm

Diameter: 2, 1.5 mm
Maximum length: 37 mm - 101 mm
Force: 115, 25, 60 N

This circular saw mounting has metal interleaf has been incorporated into the design, providing higher compression to shear stiffness ratio and therefore increasing the compressor's load capacity, as well as the combined compression and ...

Maximum length: 24 mm

Made from POM, Nylon 66, PC, Silicone, Silicon oil Clip base damper for snap mounting Damping torque 20rpm at 20?C Temperature range: -40 +90?C Lifetime 100,000 cycles A: Torque (Ncm), B: Module, C: Nr of Theet D: Pitch Circle ? wheel, ...

Diameter: 15 mm
Force: 12 N

Rotary Dampers - Without Gear control the speed and acceleration of a movement in a travelling body. Simple to install, they can be fitted as part of an assembly. Available in a range of torques and gear profiles

The THZ Series is manufactured by Ponar. It is a hydraulic damper type that has a working temperature ranging from -30 up to 50?C. It has a tank capacity of 350 cm and a stroke of 70 mm. Furthermore, this device is suitable to limit speed ...

Diameter: 0.59, 0.87 in
Maximum length: 6.5 in - 18.2 in

Dampers are designed to influence the characteristics of movement. Providing controlled arrest of a weight or lid they are used across a variety of industrial applications. Camloc dampers are self contained oil filled rod and tube assemblies ...

Elastic all-metal-cushions made of stainless steel wire applying a special production technique, used as structural elements in round, rectangular and almost every other extraordinary shape or available as stud mounts. Load range depending ...

Mounts type GST series are utilised when a vertical adjustment for the balancing of surface irregularities, or the exact alignment for the placement of a machine are needed.The load range of the mounts lies between 250 daN and 800 kN.

Reduces vibration in resonance area of stepping motors Assists to follow pulse speed in the range of high rotational speed and enhance maximum rotational speed of stepping motors Operational Temperature: -10?~40? Finished ...